Tiger Products Co., Ltd JD 5083E User Manual Page 95
- Page / 182
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Cheetah Maintenance Section 4-17
MAINTENANCE
BEARING INSTALLATION
1 – Press upper bearing cup into the spindle housing.
2 – Turn the spindle housing over and press in the lower bearing cup.
3 – Place the lower bearing cone in the bearing cup. Next press the seal into the
spindle housing. The inner lip of the seal must be DOWN, towards the bearing, so
lubricant is sealed inside the housing.
4 – Install the spindle in the housing. Lightly press the spindle to seat the cone onto the
spindle.
5 – Support the bottom of the spindle and press the upper bearing cone and bearing
adjustment sleeve onto the spindle.
NOTE: The spindle housing must turn freely when seating the bearing cone and sleeve.
6 – Press the two upper seals into the spindle housing. The inner lip of the seals must
be UP, away from the bearing, so excess lubricant can escape.
7 – Install the bearing adjustment nut (thin nut) so there is 1/16” clearance between the
nut and the sleeve. Install the jam washer, placing the tab into the key-way. Install the
bearing lock nut (thick nut) and hand tighten against jam washer and adjustment nut.
See the following section for bearing adjustment.
8 – Position the spindle housing horizontally with the drain hole oriented “up.” Grease
through the zerk with Tiger Spindle Lubricant(part number 06540000) until the grease
purges from the drain hole.
9 – Install the plug into the drain hole.
- CHEETAH BOOM 1
- ASSEMBLIES 1
- TABLE OF CONTENTS 5
- Cheetah Safety Section 1-1 7
- YOU! Only YOU can 8
- (SG-19) 11
- Cheetah Safety Section 1-15 21
- 00769737 21
- 00725746 21
- Cheetah Safety Section 1-16 22
- 02962764 22
- 02962765 22
- 02965262 22
- Cheetah Safety Section 1-17 23
- 02971123 23
- 03200285 23
- Cheetah Safety Section 1-18 24
- Cheetah Safety Section 1-19 25
- Cheetah Safety Section 1-20 26
- Cheetah Safety Section 1-24 30
- Cheetah Safety Section 1-25 31
- HYDRAULIC TANK 32
- FEDERAL LAWS AND REGULATIONS 34
- ASSEMBLY 35
- TRACTOR PREPARATION 36
- CRANKSHAFT ADAPTER 36
- MAIN FRAME MOUNTING 37
- ADJUSTING REAR WHEELS 37
- POLYCARBONATE SAFETY WINDOW 37
- 3-POINT BOOM REST MOUNTING 38
- AXLE BRACE 38
- JOYSTICK SWITCH BOX MOUNTING 39
- JOYSTICK SWITCH BOX WIRING 40
- JOYSTICK CONTROL MOUNTING 41
- VALVE MOUNTING 41
- DANFOSS VALVE PLUMBING 43
- (WITH MID-MOUNT VALVE) 43
- HOSE AND CABLE ROUTING 48
- CHEETAH HOSE ROUTING 50
- HYDRAULIC TANK INSTALLATION 52
- GENERAL HOSE INSTALLATION 52
- SWIVEL BRACKET MOUNTING 52
- DECK ATTACHMENT 53
- BOOM INSTALLATION 53
- HOSE COVERING 53
- PREFORMED TUBE INSTALLATION 53
- WHEEL WEIGHT MOUNTING 54
- INSTALLING O-RING FITTINGS 54
- MOWER TESTING 59
- 4WD FRONT TIRE ADJUSTMENT 60
- OPERATION 61
- STARTING TRACTOR AND MOWER 63
- JOYSTICK CONTROL SWITCH BOX 64
- JOYSTICK CONTROL 66
- (ON SWITCH BOX) 67
- LEVER CONTROL AND FUNCTIONS 68
- MOWER OPERATION 70
- UNSTOWING BOOM 70
- TRANSPORTING MOWER 72
- INSPECTION SHEETS 74
- MAINTENANCE 79
- MAINTENANCE PRECAUTIONS 80
- BREAK IN PERIOD 80
- REGULAR MAINTENANCE 81
- WEEKLY OR EVERY 50 HOURS 82
- MONTHLY OR EVERY 150 HOURS 82
- YEARLY OR EVERY 500 HOURS 82
- TROUBLE SHOOTING 82
- TORQUE SPECIFICATIONS 84
- LUBRICATION RECOMMENDATIONS 85
- DETAILED MAINTENANCE 87
- GREASING SPINDLE 89
- TIGHTENING SPINDLE BOLTS 90
- GREASING THE BOOM SWIVEL 91
- BALL VALVES 92
- BOOM FLAIL KNIFE REPLACEMENT 93
- THE SPINDLE ASSEMBLY 94
- BEARING INSTALLATION 95
- BEARING ADJUSTMENT 96
- DAILY MAINTENANCE SCHEDULE 97
- JD 5101E - CHEETAH BOOM MOWER 99
- PARTS ORDERING GUIDE 100
- Parts Section 5-3 101
- Parts Section 5-4 102
- Parts Section 5-6 104
- Parts Section 5-8 106
- Parts Section 5-10 108
- Parts Section 5-12 110
- Parts Section 5-13 111
- Parts Section 5-14 112
- Parts Section 5-16 114
- SWITCH BOX AND JOYSTICK 5101E 116
- LIFT VALVE - JOYSTICK CONTROL 118
- CABLE CONTROLS - SCV ONLY 120
- Parts Section 5-24 122
- WHEEL SPACER 126
- WHEEL WEIGHT ASSEMBLY 127
- Parts Section 5-30 128
- CHEETAH BOOM MOWER 129
- Cheetah Common Section 6-3 131
- Cheetah Common Section 6-4 132
- CHEETAH BOOM ARM ASSEMBLY 134
- CHEETAH ROTARY MOWER DECK 136
- CHEETAH ROTARY PIVOT ASY 138
- DAN FOSS VALVE (06502095) 140
- Cheetah Common Section 6-14 142
- ITEM PART NO. QTY DESCRIPTION 143
- Cheetah Common Section 6-16 144
- Cheetah Common Section 6-18 146
- CHEETAH ROTARY MOTOR 148
- ROTARY SPINDLE ASSEMBLY 150
- CHEETAH FLAIL HEAD ASSY 152
- Cheetah Common Section 6-26 154
- CHEETAH FLAIL MOTOR 156
- CHEETAH CYLINDER BREAKDOWNS 158
- BOOM TRAVEL LOCK 164
- BRAKE VALVE TROUBLESHOOTING 165
- Cheetah Common Section 6-39 167
- HUSCO CONTROLS SWITCHBOX 168
- INTENSIONALLY 169
- OPTIONAL PUMP GUARD KIT 170
- TROUBLESHOOTING 172
- Cheetah Common Section 6-46 174
- Cheetah Common Section 6-47 175
- Cheetah Common Section 6-48 176
- WARRANTY 177
- WARRANTY INFORMATION 179
- ONE LAST WORD 180
- YOU. Common sense should 180
- Printed in USA 182
- © Tiger Corporation 182
Related products and manuals for Lawnmowers Tiger Products Co., Ltd JD 5083E
(186 pages)© 2020, manymanuals.com. All rights reserved. | 0.571 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals